TERUFLEX Blood Anticoagulant Citrate Phosphate Dextrose Adenine (CPDA-1) For Collection Of

Assure that the White Clamp below the pouch is closed prior to initiating phlebotomy. 10. Secure the needle safety device in place following the device instructions provided on the reverse side. 11. Secure donor tubing to donor's arm. 12.

Position the diversion pouch with the notches up and the Tube Holder/Luer Adapter assembly (or port cap) down. When the level of blood in the pouch is approximately in line with the notches, the diversion pouch is full (Fig. 3a). 1.

NOTE:

The approximate fill volume of the pouch at the notches is 35 mL. 13. Permanently seal the tubing between the "Y" and the diversion pouch to maintain a closed system using an aluminum clip or a tube sealer approved for use with tubing connected to a donor (Fig.

3b). 1.

CAUTION:

Do not use a dielectric tube sealer to seal the tubing while the needle is connected to the donor's body unless it is approved for such a purpose. 14. To initiate blood flow into the collection bag, break the CLIKTIP between the "Y" and the collection bag.

15. To avoid clot formation, collect samples as soon as possible from the diversion pouch as follows (Fig. 3b). 1.

CAUTION:

Do not collect donor test samples until the tubing between the "Y" and the diversion pouch is permanently sealed. 2. Open the White Clamp on the tubing below the pouch to open the pathway for sampling. 3. Position the diversion pouch with the notches up and the Tube Holder/Luer Adapter assembly downward.

Assure that any air in the pouch is at the top and will not enter the blood collection tubes. 4. Insert blood collection tube firmly into the tube holder; when full, remove sample tube from holder. Repeat to collect additional samples.

5.

NOTE:

The pouch may be removed after the donor test samples are collected. A second seal must be made between the diversion pouch and the permanent seal prior to removing the pouch. 16. Mix blood with anticoagulant in the collection bag and continue to mix at several intervals during collection and immediately after collection.

If using an automated mixer, follow manufacturer's instructions. 17. Collect labeled volume of blood 450 mL ±10% or 500 mL ±10%. 18. 3. Make a second seal between the first seal or knot and the "Y". Various methods may be used to seal tubing.

19. Release pressure on the donor's arm and remove the needle into the needle safety device following the device instructions provided on the reverse side. Sever the donor tubing between the two seals previously made below the CLIKTIP and "Y".

1.

CAUTION:

Discard the Diversion Blood Sampling Arm and phlebotomy needle/donor tubing according to institutional standard operating procedures. 20. Strip blood from donor tubing into collection bag, mix well, and allow tubing to refill; repeat once.

To prevent the blood from clotting in the tubing, work quickly as possible. Make an appropriate number of segments of anticoagulated blood for testing by sealing on or near the X marks. Leave segments attached to the Whole Blood unit.

21. The time between Whole Blood collection and component separation may vary depending on both the blood bag system and processing options selected. Follow your institution's standard operating procedures to prepare components. 1. If the Whole Blood is to be processed into room temperature components, maintain the blood at ambient temperature.

2. g. during transport) and then placed in storage at a temperature between 1-6°C upon arrival at the processing center. 22. Platelet Rich Plasma and Platelets should be separated from the Red Blood Cells within 8 hours of blood collection, if prepared.

23. Plasma intended for production of Fresh Frozen Plasma should be separated from the Red Blood Cells and placed in a freezer at –18°C or colder within 8 hours of blood collection. 24. Plasma intended for production of Plasma Frozen Within 24 Hours After Phlebotomy (PF24) should be placed in a freezer at -18°C or colder within 24 hours of blood collection.

25. For further preparation and processing of other plasma components, use standard processing and storage techniques following approved regulations and standards. 26. Select the appropriate spin condition and centrifuge Whole Blood unit to separate CPDA-1 Red Blood Cells from plasma or platelet rich plasma, as appropriate.

27. Break the CLIKTIP of primary collection bag and transfer plasma into satellite bag, or transfer platelet rich plasma into XT-612 Platelet bag. Clamp transfer tubing of satellite bag. 28. Seal tubing of primary collection bag in two places, cut between seals, and if applicable, separate from satellite bag(s).

29. Store CPDA-1 Red Blood Cells (or Whole Blood) between 1 – 6°C for up to 35 days. 30. If prepared, store Platelets between 20-24°C, maintaining a continuous gentle agitation, for up to 5 days in XT-612 bag. Fig. 1, Fig. 2a, Fig. 2b Fig.

3a, Fig. 3b

Not medical advice. Always read the patient information leaflet and follow your prescriber or pharmacist.